California Leads the Way in Environmental Legislation

California is noted for taking the lead in environmental legislation, particularly in clean air and energy conservation. Recent legislation in California underscores the merits of using white coatings like those from Conklin on commercial buildings to reduce energy costs.

California Title 24 legislation is exemplary for its support of white coatings. Exempting buildings with high-reflectance roofing from energy audits makes sense because white coatings dramatically decrease the need for insulation and air conditioning.

Alleviating solar heating loads directly affects peak electricity requirements. Peak electric loads are often the basis for the price of electricity because they establish the energy generating needs of a region.

California Title 24 legislation requires a detailed energy audit on a new building, to show that solar heat is dissipated or removed in an energy efficient manner, e.g., through insulation and climate control systems, unless the building uses highly reflective roofing with reflectance values above 0.70. Hence, Title 24 sends a strong message to building designers: The best way to cool a building is to divert the solar energy before it raises temperatures.

Look for a Conklin Roofing Systems contractor in your area:



ROOFING CONTRACTORS NEEDED IN MULTIPLE STATES!
Patton Services | (309) 303-3128 | rpatton55@comcast.net | http://www.whiteroofingsystems.com

Conklin Roof Coatings - Beautiful, Energy Efficient Roof Systems

Video taken by Conklin Roofing Contractors Mike & Jodi Stout of Stout Roofing & Construction (Havana, IL)

Conklin Roofing Systems have been applied to over 2 billion square feet of roofing throughout the United States since 1977.

Conklin’s white roofs reflect the sun’s hot UV rays rather than absorbing them the way black roofs do. Conklin roofing systems & roof coatings have been proven to be energy efficient in some very intense situations and under some very intense scrutiny.

Conklin offers a variety of highly energy efficient roof coating products including Benchmark®, Rapid Roof III®, and Equinox™ Top Coat.

Look for a Conklin Roofing Systems contractor in your area:



ROOFING CONTRACTORS NEEDED IN MULTIPLE STATES!
Patton Services | (309) 303-3128 | rpatton55@comcast.net | http://www.whiteroofingsystems.com

Foam Roofing at Texas A&M University

According to Gerald Scott (former Director of Energy at Texas A&M University), the campus at College Station, Texas began re-roofing their facilities using polyrethane foam like that from Conklin. Why? Because it works!

Polyrethane foam fills in any cracks and smooths over any seams or irregularities on a roof system. The potential for leaks is virtually eliminated, keeping water out and energy in.

Texas A&M University kept careful records on the performance of their roofing systems and found that they have had reductions in maintenance costs as well as decreased energy expenses.

Of the 10 million square feet of roof area at the central campus, over 90% are now protected by spray polyrethane foam. Texas A&M uses no other roof system for new or remedial roofing.

From 1980 to 1984, 27 buildings with a total of 593,529 square feet of roof area were re-roofed with spray polyrethane foam. The construction costs totaled $1.7M. Annual energy savings total $327,460, resulting in a 4 1/2 year discounted return on investment.

The bottom line? Spray polyrethane foam is an effective and relatively inexpensive roofing system to install, and provides the benefits of energy efficiency to help pay back the cost of the re-roofing you needed anyway.

Look for a Conklin Roofing Systems contractor in your area:

ROOFING CONTRACTORS NEEDED IN MULTIPLE STATES!

Patton Services | (309) 303-3128 | rpatton55@comcast.net | http://www.whiteroofingsystems.com

Liquid-Applied Membranes are Excellent for Re-Covering Roofs

There are two installation options with liquid-applied membranes like those from Conklin: squeegee and spray application. Spray application is generally used with coated-polyurethane-foam systems. Liquid applied systems are highly useful as re-covers for weight-sensitive applications, such as pre-engineered steel buildings.

Coated-polyurethane-foam systems are excellent for adding insulating value to a re-cover roof and fixing slope-to-drain problems. They are sensitive to humidity during installation. If a silicone coating is used, the roof system is not sensitive to grease and oil emissions as silicone is fairly inert.

Squeegee-applied systems are mostly used to prolong the life of an existing smooth-surface roof. They are a good, low-cost alternate to reroofing but are not necessarily a permanent replacement. Newer, liquid-applied roofing systems can last as long as 10 years, however. The caveat is that the roof has to be in fairly stable and dry condition when the new liquid membrane is applied.

Clearly, there are many options available to anyone undertaking a re-roofing project. Sorting them out before going out to bid is the best way to assure the most appropriate roof system is chosen for the building. A properly trained and knowledgeable roofing contractor can help sort through the options.

For those who are not currently working with a particular contractor or who feel uncomfortable having the same entity designing and installing the roof, an architect or engineer who specializes in roof consulting can not only sort out the best options, but also provide construction documents that will allow you to bid out the same work to the best contractors and know that the roof has been optimized to fit the building.

Look for a Conklin Roofing Systems contractor in your area:

ROOFING CONTRACTORS NEEDED IN MULTIPLE STATES!

Patton Services | (309) 303-3128 | rpatton55@comcast.net | http://www.whiteroofingsystems.com

Single-Ply Membranes are Good for Most Re-Cover Jobs

The options are widespread with single-ply membranes. There are two major generic types of membranes with three major generic types of installation methods. There are the thermoset membranes — cured membranes with seams that are sealed with adhesives — and thermoplastic membranes with seams that are heat- or solvent-welded. The systems are either fully adhered, mechanically attached, or loose-laid and ballasted.

Single-ply membranes are good choices for most re-covers because they are lightweight and can re-cover almost any deck type. Single-ply membranes are a good choice when first cost is the overriding factor in the installation because they usually are less expensive to install.

EPDM is worth considering when the roof is wide open with large empty expanses because it is available in 10- and 20-foot wide rolls, minimizing seams. In these situations, repairs to membranes using electrical heat welders may be a problem without a very long extension cord. On the other hand, for roofs with densely packed, multiple penetrations, thermoplastics offer smaller roll sizes; membranes with large roll sizes are more difficult to install around closely packed penetrations.

Mechanically attached membranes are generally not the preferred way of installing single plies over structural concrete decks but are good for use on steel or wood. A fully adhered or ballasted system is more appropriate for structural concrete to avoid damage to the concrete.

Single-ply membranes should be evaluated for chemical composition if they are being installed where hydrocarbon emissions are a problem. PVC- and EPDM-based membranes are sensitive to hydrocarbons, such as oil, cooking grease and jet fuel, and should not be used. Specialty formulations of single plies are available for applications where these emissions are a problem.

Look for a Conklin Roofing Systems contractor in your area:

ROOFING CONTRACTORS NEEDED IN MULTIPLE STATES!

Patton Services | (309) 303-3128 | rpatton55@comcast.net | http://www.whiteroofingsystems.com

Limitations of Modified-Bitumen Roof Membranes

Modified-bitumen options are even more complex than built-up roofing options. Not only are there two major types of modified-bitumens — those based on rubber modifiers (SBS and SEBS) and those based on plastic modifiers (APP) — but there are different installation methods that can be used with the different membranes.

Generally speaking, SBS membranes are applied with hot asphalt or cold adhesives, though they can be torch-applied. APP modifieds are generally torch-applied, but some can be adhesively applied. Almost all modified-bitumen membranes are surfaced with granules, making them less heavy than the traditional gravel-surfaced, built-up roof. Often, a modified-bitumen membrane will be used as a cap sheet on a traditional built-up roof. This gives the redundancy of a built-up roof with the flexibility of a modified membrane.

Modified-bitumens share most of the pros and cons of built-up roofing with one major difference - the modified bitumens were developed to perform better in cold weather by remaining flexible at low temperatures. They can stretch and relax with temperature changes better than built-up systems.

APP and torch-applied SBS systems should be used with care if there are flammable items on the roof, such as wood parapets. The membranes can smolder and erupt into flames long after being torched. They are the best choice of the modified-bitumen membranes if odor is a problem because there is no adhesive to flash off or asphalt to cause smells during installation. APPs and cold-adhesive-applied modifieds are equally good choices if delivery to the roof is limited, as both can be delivered via freight elevator and stairs.

Look for a Conklin Roofing Systems contractor in your area:

ROOFING CONTRACTORS NEEDED IN MULTIPLE STATES!

Patton Services | (309) 303-3128 | rpatton55@comcast.net | http://www.whiteroofingsystems.com

Limitations of Built-Up Roofs

If one roof system type could be thought of as ubiquitous, built-up roofing would certainly have that honor. Since their inception more than 100 years ago, built-up roofs have earned a tried-and-true reputation. But even this workhorse has limitations that should be considered when choosing a roof system.

Built-up roofs are preferred when there is heavy traffic or the potential for mechanical abuse on the roof, because the roof membrane tends to be thicker and more substantial than other systems. Gravel surfacing makes the roof highly resistant to normal traffic. Multiple layers mean that there is redundancy in the roof. Built-up roofing is familiar, so if a facility is located in an area with a limited choice of roofing contractors, it is almost certain that at least one will be competent to handle the installation and repair of a built-up roofing system.

Care must be taken with a built-up roof if wide-open expanses of roof exist or if there is movement within the structure itself. In a traditional built-up roofing system, the ability to stretch and relax because of thermal or structural movement is limited to about 10%. Where the building is very long, additional curbs must be built into the roof to keep the area of expansion and contraction within manageable limits. This may become a problem if these curbs must be positioned to not interfere with drainage.

Cold-weather installation raises other issues. Cold temperatures adversely affect the installation of the roof because the material is not flexible at low temperatures, and low asphalt temperatures will cause non-adhesion of the reinforcing felts.

If long pipe lengths are required to reach the roof from the kettle, the asphalt can cool too much before it reaches the application point, causing poor installation.

Built-up roofs can also be installed with cold adhesives that solve many of the temperature-at-application-point problems associated with hot asphalt. Ease of materials delivery is also a consideration in choosing a cold-applied system as the materials can be brought up a freight elevator and delivered to the roof. If odor or VOCs are a consideration, most cold adhesives flash off solvents as they cure.

Built-up roofs are generally not the best choice for re-cover systems because they are heavier than most other types of roof systems, and the added weight may preclude a re-cover. Built-up roofing should not be chosen when the roof is subject to heavy coatings of grease and oil as hydrocarbon materials will dissolve the waterproofing asphalt.

Look for a Conklin Roofing Systems contractor in your area:



ROOFING CONTRACTORS NEEDED IN MULTIPLE STATES!

Patton Services | (309) 303-3128 | rpatton55@comcast.net | http://www.whiteroofingsystems.com